Skip to content

Irrigation System Maintenance Tips in Indianapolis, Indiana

Maintenance of Irrigation Systems


With a competent home irrigation system with sprinklers, you can have green grass and a gorgeous landscape all summer long. Installing irrigation systems and sprinkler heads in the Indianapolis area allows homeowners to water their lawns and keep their yards looking lush even when the weather isn’t cooperating. However, proper operation of these devices necessitates some upkeep.

Midwest Plumbing Indianapolis explains professional irrigation system maintenance methods to keep your lawn irrigated and your irrigation system in good working order. Learn how to test irrigation components and identify the need for repairs, inspect heads to determine when to replace broken or missing sprinkler units, and adjust heads for optimal watering to save money and prevent waste.

Maintaining Your Irrigation System at the Right Time

Many homeowners in the Indy area will begin to use irrigation systems in the spring or once summer arrives. To maintain grass green in the fall, these systems and sprinkler systems can be used. Call to schedule a professional irrigation system inspection each year before you start using the irrigation equipment. A plumber must evaluate the quality and performance of your irrigation system and heads to ensure that they are in good operating order, discover and address repair concerns, and optimize positioning to deliver water efficiently.

In addition to this professional service, you must maintain your irrigation system during the watering season. These pointers will help you maintain heads and other critical components, as well as change their position, to guarantee that your grass is properly watered while wasting as little water is possible.

Maintenance Procedures for Irrigation Systems

These irrigation system maintenance suggestions will maintain heads and other equipment in good operating order throughout the spring, summer, and fall. They also assist you in fine-tuning the performance of sprinklers, heads, and irrigation systems so that your lawn remains lush while wasting neither money nor water.

Examine and test the systems

Allow the irrigation system to irrigate the lawn once a month. Even if it’s been raining a lot, go ahead and do it. To verify and check the system’s performance, you must witness it in action.

Dry areas in a zone indicate that a head is clogged, damaged, or in the incorrect position.

Check the ground for wet areas and saturated dirt, which are evidence of leaks in the water lines below ground.

Check the direction and range of each head’s water spray to ensure that the entire zone is watered; you may need to modify the head for better watering.

Examine the status of each sprinkler head in your system to discover whether any are clogged, damaged, or missing. As soon as you notice these problems, repair or replace the heads.

Sprinkler Modifications

Each sprinkler head must be appropriately directed to ensure that enough water is delivered to the entire lawn zone. Heads are readily knocked out of position when mowing the grass or by people moving around in the yard, so they must be adjusted frequently during the season. Spray heads, rotary heads, or a combination of the two are used in home irrigation systems to adequately water the landscape. Spray heads are used for a narrower zone to spray a continuous stream of water, whereas rotary heads rotate the nozzle to irrigate grass and plants across a broader area.

Keep an eye on where the water lands in each zone. You just want it to hit grass or the landscape. You’ll need to adjust the head if water strikes a hard surface like a driveway, sidewalk, or other hard surface. If there is excessive water runoff in a given region, the head may need to be modified to reduce waste. Dry areas indicate that the heads have been knocked out of position and need to be adjusted.

Adjust spray heads by twisting them so that the nozzle points in the direction you want to water.

Form a right angle between the ground and the nozzle position while adjusting rotary heads.

Lawnmowers, automobiles, and persons moving around the yard can all press heads into the earth. The head of the nozzle might become clogged while it is below the earth surface, causing the spray direction to be interrupted. Pull up any heads that are positioned this way and raise them so that the nozzle sits over the grass’s top.

Misting is a common problem caused by low water pressure, but it can lead a zone to run out of water. High water pressure causes mist to form on the heads, which quickly evaporates or is carried away by the wind. Installing a pressure regulator will control the water pressure in irrigation lines, preventing misting.

Calibration of the Irrigation System

Your lawn will not be as green and lovely as you want it to be if it receives too much or too little water. You may also be squandering money owing to water waste or the need to replace dead landscaping. It’s critical to calibrate your irrigation system so you know how much water is delivered by sprinkler heads and how long it will take to provide a specific volume of water in a zone. Calibration will assist you in determining the ideal time to use your irrigation system in order to save money and maintain your lawn healthy.

One zone at a time, calibrate irrigation systems.

5 to 10 cans should be placed throughout a zone. For proper collection, cans or containers should have straight walls and a diameter of 3 to 6 inches.

Allow at least 15 minutes for spray heads and at least 30 minutes for rotary heads in an irrigation zone. When the bulk of the cans have accumulated at least a 1/4 inch of water, turn off the irrigation system.

With a ruler, measure the depth of the water in each can. To calculate the average water depth, add the depths together and divide by the number of cans.

To calculate the run duration in hours, multiply your irrigation system’s run time in minutes by 60. Divide the average depth by the run duration in hours to get the number of inches of water delivered in that zone per hour by your irrigation system.

Program the Controller

A home irrigation system’s controller determines when the system watered the property. It’s like an irrigation system timer or clock! The watering needs of your landscape will alter with the weather, season, and other circumstances, so you’ll need to reset the controller during the watering season. You can reduce waste and save money by making frequent modifications to the controller.

Set the irrigation system to run more when it’s hot and less when it’s cool on the controller. When the weather is hot, plants need more water, and when the weather is cold, they need less.

To save money during the summer when the weather provides a lot of rain, you might turn off the controller and just run the irrigation system as needed. Installing a rain shutdown device, which detects when it is raining and turns off the irrigation system if it is operating, is another an option.

Indianapolis Irrigation System Service

Irrigation system maintenance will keep your sprinklers and components in good working order while also hydrating your grass and lawn. Call Midwest Plumbing today to schedule service if you notice any concerns such as leaks, broken heads, or other issues that require professional attention.